Bỏ qua đến nội dung chính

Hướng dẫn cho người mua

Inverter Booster Pumps for Multi-Storey Homes: Flow, Head and Pressure Setting

In many Philippine homes, water runs from a cistern to an overhead tank, then feeds the house by gravity — and the upstairs shower gets a weak stream. An inverter booster between the tank and the house fixes it.

Bởi Calliope Pumps16 November 20265 phút đọcĐã cập nhật 2026-11-16Được xem xét bởi Đội ngũ kỹ thuật Calliope
Bơm tăng áp đa tầng thép không gỉ SCS100P-3

In many Philippine homes, water runs from a cistern to an overhead tank, then feeds the house by gravity. The upstairs shower gets a weak stream because gravity alone cannot push enough pressure to the top floor. An inverter booster pump installed between the tank and the house fixes this by holding a pressure set point. This guide covers the three numbers for a multi-storey home — lift and head, simultaneous flow, and the pressure setting — then matches them to a model.

Các model được dùng làm ví dụ trong bài viết này: SCS100P-3 bơm đa tầng thép không gỉ biến tần nam châm vĩnh cửu and SPS90-3 bơm tăng áp vfd nam châm vĩnh cửu, cả hai đều được liệt kê trong bơm tăng áp đa tầng thép không gỉ một pha nhóm.

Storeys and head: how high the water must go

Each storey adds roughly 3 m of lift, so a three-storey house has its highest shower about 9 m above the pump. Head is the lift plus the friction the pipes add plus the pressure the highest outlet needs, and 1 bar is about 10.2 m of water column. For a VFD booster, the outlet pressure is the constant-pressure set point, so the required head is the set point plus lift plus friction. If the pump is fed from a pressurised mains line rather than a tank, the inlet pressure counts toward the total and the pump only has to add the difference.

Simultaneous flow: count what runs at the same time

Flow is the volume the site must deliver at the same moment, not the total of everything connected. A three-storey house with four taps, two showers and a washing machine rarely runs them all at once, so size for the realistic peak: the outlets that are actually open together at the busiest time of day, for example two showers plus a kitchen tap.

Write the peak down in litres per minute. An inflated flow figure is the most common sizing mistake: it pushes the selection to a larger pump that then runs throttled, noisy and far from its best efficiency point.

Pressure setting: what the set point should be

The VFD holds the pressure set point by changing motor speed, so the set point is the pressure the highest outlet sees. Set it high enough to cover the top shower with margin, but no higher: extra pressure is turned into noise and wear rather than useful flow, and it stresses pipes and fittings. The installer sets the point on site against the duty the house actually needs, and it can be adjusted later if the household changes.

A pump running near its design duty is quieter and draws closer to its rated input than a pump throttled far from the curve. That is why the set point and the model are chosen together, not separately.

Model comparison: a worked example

Take a three-storey house whose peak demand is 40 L/min at 28 m of head. That is the duty point: 40 L/min, 28 m. Here is how three models compare against it, using their published Q-H curves.

  • SPS-90, Cấp 5 (0.38 kW): đường cong đã công bố chạy từ 32 m ở lưu lượng bằng không tới 0 m ở 60 L/min, đi qua 25.9 m ở 30 L/min và 15.9 m ở 45 L/min. Ở 40 L/min, bơm đạt khoảng 19 m — thấp hơn 28 m mà ngôi nhà cần. SPS-90 không đáp ứng điểm làm việc này.
  • ICP100F (0.75 kW): đường cong đã công bố chạy từ 38 m ở lưu lượng bằng không tới 10 m ở 87 L/min, đi qua 32 m ở 34 L/min và 29 m ở 47 L/min. Ở 40 L/min, bơm đạt khoảng 30.6 m — cao hơn 28 m yêu cầu, với biên độ khoảng 2.6 m. ICP100F đáp ứng điểm làm việc.
  • SCS100P-3, Công suất 1 (0.55 kW): cấp công suất thấp nhất trong năm cấp của bơm đã đạt 115 L/min ở cột áp tới 46 m, và đường cong Công suất 5 của bơm đi qua khoảng 63 m ở 40 L/min. Bơm đáp ứng điểm làm việc với cột áp vượt xa nhu cầu của ngôi nhà, vì vậy nó quá lớn cho nhu cầu này — cột áp thừa sẽ bị tiết lưu mất.
  • Kết luận: ICP100F là lựa chọn phù hợp. Bơm đáp ứng điểm làm việc gần giữa đường cong, trong khi SPS-90 không đạt và SCS100P-3 là bơm lớn hơn mức ngôi nhà có thể dùng.

Voltage and water source checks

A pump that covers the duty point still fails if the site cannot power it or feed it. Philippine homes run on 220V / 60Hz, so confirm the nameplate voltage and frequency against the supply before ordering. Then check the water source: a pump fed from a cistern below the pump works on suction lift, so priming and dry-run protection matter, and the suction pipe should be short, fitted with a strainer and a non-return valve, and free of high points that trap air. If the source is an overhead tank above the pump, the inlet is flooded and suction lift does not apply.

Các bước tiếp theo

Work through the selection guide for a shortlist, then open a model page for the full specification and the Q-H curve. Send the three numbers — flow, head and voltage — with the inquiry, and our team confirms the model and replies with a quotation.

Sẵn sàng chốt thông số? Gửi lưu lượng, cột áp, nguồn điện và cỡ ống qua biểu mẫu yêu cầu , hoặc nhắn tin cho đội xuất khẩu qua WhatsApp .

Các model được nhắc đến trong bài viết này

Bài viết liên quan

Sẵn sàng trao đổi về thông số kỹ thuật, điện áp và số lượng?

Gửi thị trường mục tiêu và thông số kỹ thuật của bạn. Đội xuất khẩu của chúng tôi sẽ gửi lại báo giá B2B phù hợp.

Yêu cầu báo giá
Bán hàng & xuất khẩu
cason@calliopepump.com
Trụ sở chính
office@calliopepump.com
Điện thoại / WhatsApp
+86 178 0591 6566

Chúng tôi sử dụng cookie

Bộ nhớ thiết yếu giúp trang web hoạt động. Cookie phân tích chỉ được đặt sau khi bạn nhấn Chấp nhận. Nếu bạn từ chối, sẽ không đặt cookie phân tích nào. Thông báo về cookie