
A dB rating looks simple — one number — but it only means something when you know the distance it was measured at, the duty point the pump was running at, and the conditions around it. Two pumps with the same dB number can sound very different in a home, and a pump rated quietly can run loudly if it is sized or installed wrong. This article explains what dB means, the figures behind our range, what affects perceived noise, and how to compare two pumps honestly.
Models used as examples in this article: SPS-90 intelligent vfd booster pump and ICP100F pm vfd smart booster pump, both listed in the single-phase single-stage centrifugal boosters grupie.
What dB means
The decibel is a logarithmic scale, not a linear one. That means a small change in dB is a real change in loudness: a step of 10 dB is roughly perceived as twice as loud. A pump rated at 40 dB is not slightly quieter than one rated at 50 dB — it is perceived as about half as loud.
Distance matters just as much as the number. Sound falls with distance, so a rating is only meaningful with the distance it was measured at. Our figures are measured at 1 m from the pump. A rating quoted without a distance cannot be compared with one quoted at 1 m, because the same pump reads lower the further away you stand.
The figures behind our range
The SPS-90 is rated at or below 40 dB at 1 m when it is sized for its duty. Other models in the range are rated at or below 55 dB. Those are the company ratings — the maximum the model is rated at, not a measured value for a specific installation, and not a promise for every duty point.
A rating is a ceiling, not a guarantee. A pump running at its design duty, correctly installed, will sit at or below its rating. The same pump running far from its duty point — oversized and throttled, or undersized and straining — will be louder. That is why the rating and the sizing belong together: the number tells you what the model can do, and the duty point tells you whether your installation will get it.
What affects perceived noise
Three things decide how loud a pump sounds in a home: the duty point, the installation, and where the pump sits.
- Duty point: a pump running near the middle of its curve is quieter than one throttled far from it. Oversizing is the most common cause of a noisy pump — the extra head is turned into noise and wear rather than useful flow.
- Installation: a pump bolted firmly to a solid base, with supported pipes and no air in the suction line, runs quieter than the same pump loose on a thin panel with rattling pipes.
- Location: a pump in a utility room behind a closed door sounds different from the same pump mounted on a bedroom wall. Where the pump sits matters as much as what it is rated at.
How to compare honestly
To compare two pumps, hold the conditions equal: the same distance, the same duty point, and the same installation. Ask for the test distance behind any dB figure — a number without a distance is incomplete. Then ask what duty point the figure was measured at, because a pump rated at its best point will read higher at a duty far from it.
Also compare like with like. A single-stage booster and a multistage booster have different hydraulic designs, so their ratings sit on different bases. The honest comparison is the rating at the same distance, at the duty point your house actually needs, with the installation the rating assumes.
Installation tips for quiet operation
Most of the noise a homeowner hears is fixable at installation, not at the factory.
- Size to the duty point: pick the model whose curve covers the duty near its middle, not the largest model in the range.
- Mount firmly: bolt the pump to a solid base and keep the pipes supported so they cannot rattle.
- Keep air out: a short suction pipe, a strainer and no high points that trap air keep the pump from cavitating.
- Set the pressure point correctly: extra pressure above what the highest outlet needs is turned into noise.
Next steps
Work through the selection guide for a model that covers the duty near the middle of its curve, then open the model page for the full specification. If noise is the deciding factor, tell us where the pump will sit and what the duty point is — the SPS-90 is the quietest in the range at or below 40 dB at 1 m.
Ready to specify? Send your flow, head, power supply and pipe size through the inquiry form , or message the export team on WhatsApp .