Bỏ qua đến nội dung chính

Hướng dẫn cho người mua

Rooftop Tank Boosting for Malaysian Homes: Pressure, Setting and Sizing

In many Malaysian homes, water sits in a rooftop tank and feeds the house by gravity — and the upstairs shower gets a weak stream. A booster pump between the tank and the house fixes it.

Bởi Calliope Pumps16 November 20265 phút đọcĐã cập nhật 2026-11-16Được xem xét bởi Đội ngũ kỹ thuật Calliope
SPS-90 booster pump for rooftop tank water supply

In many Malaysian homes, water sits in a rooftop tank and feeds the house by gravity. The upstairs shower gets a weak stream because gravity alone cannot push enough pressure to the top floor — and the pressure falls further when two taps run together. A booster pump installed between the tank and the house fixes this by holding a pressure set point. This guide covers how rooftop tank gravity feed works, where the booster goes, the pressure setting, and sizing for 230 V / 50 Hz supply.

Các model được dùng làm ví dụ trong bài viết này: SPS-90 bơm tăng áp vfd thông minh and SG95 bơm ly tâm đường ống nam châm vĩnh cửu, cả hai đều được liệt kê trong bơm tăng áp ly tâm đơn tầng một pha nhóm.

How rooftop tank gravity feed works

A rooftop tank feeds the house by gravity: the pressure at any tap depends on how far below the tank it sits. A tap on the ground floor, several metres below the tank, gets reasonable pressure. A shower on the top floor, close to the tank level, gets very little — and the pressure falls further whenever another tap opens, because the same head is shared across more outlets.

That is why the complaint is almost always the same: the downstairs taps are fine and the upstairs shower is weak. Gravity feed works when the tank is high above the outlets and only one outlet runs at a time. In a two- or three-storey home with a family using water together, it does not.

Where the booster goes

The booster sits between the rooftop tank and the house, so it takes the tank water and pushes it into the house pipework at a steady pressure. The tank is above the pump, so the inlet is flooded by gravity and the pump does not work on suction lift — that is the easy part of the installation.

Keep the pipe from the tank to the pump short and fit a strainer, so debris from the tank does not reach the pump. Fit a non-return valve so water cannot flow back into the tank when the pump stops. If the tank is ever drained for cleaning, the pump's dry-run protection stops it before it runs dry.

Pressure setting: what the set point should be

The VFD holds the pressure set point by changing motor speed, so the set point is the pressure the highest outlet sees. Set it high enough to cover the top shower with margin, but no higher: extra pressure is turned into noise and wear rather than useful flow, and it stresses pipes and fittings.

The installer sets the point on site against the duty the house actually needs, and it can be adjusted later if the household changes. A pump running near its design duty is quieter and draws closer to its rated input than a pump throttled far from the curve — which is why the set point and the model are chosen together, not separately.

Sizing for the home

Sizing starts with the same two numbers as any booster selection: simultaneous flow and head. Flow is the volume the house must deliver at the same moment — the outlets actually open together at the busiest time of day, for example two showers plus a kitchen tap. Head is the lift from the pump to the highest outlet, plus pipe friction, plus the pressure the highest outlet needs.

An inflated flow figure is the most common sizing mistake: it pushes the selection to a larger pump that then runs throttled, noisy and far from its best efficiency point. Size for the realistic peak, and check the duty point against the published Q-H curve for the model before ordering.

Voltage and supply

Malaysian homes run on 230 V / 50 Hz, so confirm the nameplate voltage and frequency against the supply before ordering. The single-phase range covers 170–250 V, which includes 230 V with margin for mains swings. If the house has an older or unstable supply, confirm the voltage range on the model page — a pump that cannot cover the local swing will not hold its set point.

Các bước tiếp theo

Work through the selection guide for a shortlist, then open a model page for the full specification and the Q-H curve. Send the three numbers — flow, head and voltage — with the inquiry, and our team confirms the model and replies with a quotation.

Sẵn sàng chốt thông số? Gửi lưu lượng, cột áp, nguồn điện và cỡ ống qua biểu mẫu yêu cầu , hoặc nhắn tin cho đội xuất khẩu qua WhatsApp .

Các model được nhắc đến trong bài viết này

Bài viết liên quan

Sẵn sàng trao đổi về thông số kỹ thuật, điện áp và số lượng?

Gửi thị trường mục tiêu và thông số kỹ thuật của bạn. Đội xuất khẩu của chúng tôi sẽ gửi lại báo giá B2B phù hợp.

Yêu cầu báo giá
Bán hàng & xuất khẩu
cason@calliopepump.com
Trụ sở chính
office@calliopepump.com
Điện thoại / WhatsApp
+86 178 0591 6566

Chúng tôi sử dụng cookie

Bộ nhớ thiết yếu giúp trang web hoạt động. Cookie phân tích chỉ được đặt sau khi bạn nhấn Chấp nhận. Nếu bạn từ chối, sẽ không đặt cookie phân tích nào. Thông báo về cookie