Skip to main content

Tylko silnik — bez części mokrej pompy. Dla producentów pomp oraz zamówień OEM / ODM.

Silnik z magnesami trwałymi P800/1500 dla producentów pomp

Silniki PM z magnesami trwałymi

P800/1500Silnik PM z magnesami trwałymi

The P800/1500 is a permanent magnet motor only: no wet end, no suction lift, no flow or head. Manufacturers fit it to their own wet ends to build centrifugal, peripheral, jet or deep-well pumps. Two sizes: the P800 at 750 W and the P1500 at 1500 W, both with a standard shaft and locating ring. Five constant-pressure shifts are set from the panel, starting on Shift 3 at 0.22 MPa. Bearing-free inner water cooling runs at about 38 dB.

P800
750 W
P1500
1500 W
Biegi
5
Hałas
38 dB
Pobierz kartę katalogową (PDF) Zamów próbkę

Kluczowe zalety

Cechy po stronie silnika, opublikowane dla producentów pomp i zamówień OEM.

  • Motor only — the only non-pump page in the range, made for pump manufacturers and OEM/ODM orders.
  • Five constant-pressure shifts from the panel, starting on Shift 3 at 0.22 MPa by default.
  • Standard shaft and locating ring fit centrifugal, peripheral, jet and deep-well wet ends.
  • Bearing-free construction with inner water cooling, running at about 38 dB.

Dane techniczne

Dane gabarytowe dla dwóch rozmiarów silników, zgodnie z katalogiem.

TypPower (W)Prąd (A)Voltage (V)Input (Hz)RPM range (r/min)Shaft D (mm)Locating D (mm)Size (mm)Weight (kg)
P8007504.2175–26050–602500–460015110D165 × 2505.6
P150015008.3175–26050–602500–420020130D165 × 2507.2

Przesuń tabelę w bok, aby zobaczyć wszystkie kolumny.

Wymiary montażowe (mm)

P1500 mounting dimensions are not given in the source data.

RamaABCDEFGHIJ
P800168185.81524.514611574.5135102
P1500

Przesuń tabelę w bok, aby zobaczyć wszystkie kolumny.

Tryb pracy przy stałym ciśnieniu

Domyślny tryb po włączeniu zasilania, z pięcioma biegami stałego ciśnienia.

Press the power button to start the motor and enter Constant Pressure Operating Mode, the default mode. The motor starts on Shift 3, at a constant pressure of 0.22 MPa (pressure settings vary by pump type).

Press the shift button to cycle through the shifts. Five shifts are available, from lower to higher constant pressure.

Pięć biegów

Bieg

1

Bieg

2

Bieg

3

Bieg

4

Bieg

5

Domyślnie przy uruchomieniu: bieg 3, 0,22 MPa. Wartości ciśnienia dla pozostałych biegów różnią się w zależności od typu pompy i są ustawiane na panelu.

Pliki do pobrania

Karta katalogowa, krzywa wydajności i dane wymiarowe dla tego modelu.

  • kartę katalogową

    Model, key specifications, power stage data and packing details generated from the catalog data on this page.

  • Performance Curve

    Head and flow curve for this model, redrawn from the catalog axis ranges.

  • Dimension Data

    Dimension table for each model in the range, in millimetres and inches.

Dostarczasz silniki producentom pomp?

Wyślij typ części mokrej, napięcie, szczegóły wału i ilość zamówienia, aby otrzymać wycenę OEM.

Używamy plików cookie

Niezbędne pliki są potrzebne do działania strony. Pliki cookie analityczne są ustawiane dopiero po kliknięciu „Akceptuj”. W przypadku odmowy nie są ustawiane żadne pliki cookie analityczne. Informacja o plikach cookie